Cummins 6.7L Banks Power Monster-Ram Intake Elbow
Price Match Guarantee
Found it for less but value our service?
Details
Cummins 6.7L Banks Power Monster-Ram Intake Elbow
4-inch CNC machined inlet. Four 1/8-inch NPT ports designed for optimal atomization of water-methanol or NOS. Accommodates stock mounting points. Optimizes air pressure and distribution into the intake manifold. Includes proprietary #1 fuel line, 4 to 3.5-inch hump hose, and all necessary hardware. Not emissions compliant.
Key Features
- Four 1/8 inch NPT ports (Top ports targeted for optimal atomization of Straight-Shot water-methanol)
- Includes fuel line, 4 to 3.5-inch hump hose, and all necessary hardware
- Optimizes air pressure and distribution going into the intake manifold
- Raises boost without increasing turbine drive pressure
- Includes Fuel Line and all necessary hardware
- Improves flow of oxygen-rich air into cylinders
- Larger and less restrictive than stock intake
- Accommodates stock mounting points
- Outflows stock over 110-133 percent
- 4.0 inch CNC machined inlet
- Natural Bare or Red Powder-Coated Finish
The Monster-Ram improves airflow from the intercooler and flows 1008 cfm (77.01 lbs/min) compared to Stock's measly 432 cfm (33.00 lbs/min). It raises boost without increasing backpressure at the turbine which results in a more responsive and power efficient engine. Up to four 1/8 inch NPT ports are pre drilled to measure pressure, temperature, or flow. The top two NPT ports are positioned to allow for proper atomization directly into the center of the air mass. Accommodates stock mounting points including Temperature and Pressure sensors, wire harness, and dipstick tube.
At Banks Power, just enough is never enough when it comes to engine airflow. Maximum power, performance, and efficiency are the ultimate goals. To make it all happen the engine has to breathe freely and without needless restrictions. Finding ways to pump your engine full of cooler, denser air has always been the key.
Our High-Ram intakes have always whipped the competition. Our new Monster-Ram flat-out destroys it. Monster ram is CNC ported to a full 4.0 inches and was designed utilizing the latest in electronic computational fluid-dynamic technology. Next it was tested on the flow bench and dyno, then finally proven in the real world where the rubber meets the road. The Monster-Ram is a beast that only Banks could have unleashed. A simple, direct-replacement casting, Monster-Ram is instant power, performance, and acceleration gratification.
It's the perfect upgrade whether you're just starting out or working to build a serious, purpose-built race machine.
Fitment Note:
- Will not work with stock boost tube
- Part of the Banks Racing line
- Does not accommodate emissions equipment
- This is for Pure Race Use Only. Emissions equipment must be removed and requires a special ECM program available from others
- Add the Billet Heater Delete Kit for optimal power (6.7L 1st Gen use P/N 42712) (6.7L 2nd Gen use P/N 42714)
Requires Banks Boost Tube Upgrade or custom boost tube
Cummins 6.7L ISB early 1st Gen
- Driver & Passenger tubes - 25990 Boost Tube kit
- Driver side only - 25991 Boost Tube kit
Cummins 6.7L ISB late 1st Gen
- Driver & Passenger tubes - 25998 Boost Tube kit
- Driver side only - 25997 Boost Tube kit
Cummins 6.7L ISB 2nd Gen
- Driver & Passenger tubes - 25992 Boost Tube kit
- Driver Side only - 25994 Boost Tube kit
FOR RACE USE ONLY.
Does not have provisions for emissions equipment.
For street-driven vehicles, choose Monster-Ram Gen 2.
More Information
| Part Number | 403.67 |
|---|---|
| Brand | Banks Power |
| Type of Part | Intakes |
| Engine Fitment | Cummins 6.7L |
| Length | 15 |
| Width | 15 |
| Height | 12 |
| Weight | 12.000000 |
Reviews
Fitment
Cummins 6.7L Banks Power Monster-Ram Intake Elbow
4-inch CNC machined inlet. Four 1/8-inch NPT ports designed for optimal atomization of water-methanol or NOS. Accommodates stock mounting points. Optimizes air pressure and distribution into the intake manifold. Includes proprietary #1 fuel line, 4 to 3.5-inch hump hose, and all necessary hardware. Not emissions compliant.
Key Features
- Four 1/8 inch NPT ports (Top ports targeted for optimal atomization of Straight-Shot water-methanol)
- Includes fuel line, 4 to 3.5-inch hump hose, and all necessary hardware
- Optimizes air pressure and distribution going into the intake manifold
- Raises boost without increasing turbine drive pressure
- Includes Fuel Line and all necessary hardware
- Improves flow of oxygen-rich air into cylinders
- Larger and less restrictive than stock intake
- Accommodates stock mounting points
- Outflows stock over 110-133 percent
- 4.0 inch CNC machined inlet
- Natural Bare or Red Powder-Coated Finish
The Monster-Ram improves airflow from the intercooler and flows 1008 cfm (77.01 lbs/min) compared to Stock's measly 432 cfm (33.00 lbs/min). It raises boost without increasing backpressure at the turbine which results in a more responsive and power efficient engine. Up to four 1/8 inch NPT ports are pre drilled to measure pressure, temperature, or flow. The top two NPT ports are positioned to allow for proper atomization directly into the center of the air mass. Accommodates stock mounting points including Temperature and Pressure sensors, wire harness, and dipstick tube.
At Banks Power, just enough is never enough when it comes to engine airflow. Maximum power, performance, and efficiency are the ultimate goals. To make it all happen the engine has to breathe freely and without needless restrictions. Finding ways to pump your engine full of cooler, denser air has always been the key.
Our High-Ram intakes have always whipped the competition. Our new Monster-Ram flat-out destroys it. Monster ram is CNC ported to a full 4.0 inches and was designed utilizing the latest in electronic computational fluid-dynamic technology. Next it was tested on the flow bench and dyno, then finally proven in the real world where the rubber meets the road. The Monster-Ram is a beast that only Banks could have unleashed. A simple, direct-replacement casting, Monster-Ram is instant power, performance, and acceleration gratification.
It's the perfect upgrade whether you're just starting out or working to build a serious, purpose-built race machine.
Fitment Note:
- Will not work with stock boost tube
- Part of the Banks Racing line
- Does not accommodate emissions equipment
- This is for Pure Race Use Only. Emissions equipment must be removed and requires a special ECM program available from others
- Add the Billet Heater Delete Kit for optimal power (6.7L 1st Gen use P/N 42712) (6.7L 2nd Gen use P/N 42714)
Requires Banks Boost Tube Upgrade or custom boost tube
Cummins 6.7L ISB early 1st Gen
- Driver & Passenger tubes - 25990 Boost Tube kit
- Driver side only - 25991 Boost Tube kit
Cummins 6.7L ISB late 1st Gen
- Driver & Passenger tubes - 25998 Boost Tube kit
- Driver side only - 25997 Boost Tube kit
Cummins 6.7L ISB 2nd Gen
- Driver & Passenger tubes - 25992 Boost Tube kit
- Driver Side only - 25994 Boost Tube kit
FOR RACE USE ONLY.
Does not have provisions for emissions equipment.
For street-driven vehicles, choose Monster-Ram Gen 2.
